Concrete Surface Profile: How Floors Are Prepared for Epoxy Coatings

Quick answer: Concrete surface profile (CSP) is the texture of prepared concrete, rated from CSP 1 (nearly flat) to CSP 10 (very rough). Each epoxy product specifies the profile it needs, often CSP 3 to 4 for a standard floor coating. The floor must also be clean, sound and dry enough before the primer goes down.

Why does concrete surface profile matter for epoxy?

Epoxy bonds by gripping into the surface of the concrete. On smooth or contaminated concrete it has nothing to hold on to, and it peels or blisters under forklift traffic. Poor surface preparation is one of the most common reasons epoxy floors fail early.

Good preparation does three things:

  • Removes the weak top layer (laitance), old coatings and contamination.

  • Opens the surface to the texture the coating needs.

  • Exposes sound concrete that the coating can bond to.

Accurate Maintenance Services (AMS) uses concrete floor grinding to open the concrete to the right profile and to grind down high spots and lips before coating. Done right, preparation lets the coating deliver the benefits of commercial epoxy floor coatings for years.

What do CSP numbers mean?

The CSP scale comes from the International Concrete Repair Institute (ICRI) guideline 310.2R-2013, Selecting and Specifying Concrete Surface Preparation for Sealers, Coatings, Polymer Overlays, and Concrete Repair. It defines ten profiles:

  • Low numbers: light texture, for sealers and thin coatings.

  • Middle numbers: medium texture, for most epoxy floor coatings.

  • High numbers: heavy texture, for thick overlays and concrete repair mortars.

This is a general guide. The coating manufacturer's data sheet sets the exact profile for its product. For example, the Sikafloor-161 US data sheet, an epoxy primer, calls for CSP 3 to CSP 4. Thicker epoxy systems usually need a rougher profile than thin roll-on coatings.

Ask the coating installer for the data sheet of the full system, including primer, and write the required CSP into the preparation scope before the work is priced.

Grinding or shot blasting: which is better?

Both produce a good profile for epoxy. The right choice depends on the floor:

  • Diamond grinding: rotating diamond tools cut the surface down. Grinding also flattens high spots and lips at joints and removes old coatings. It reaches closer to walls and columns and suits floors that need leveling.

  • Shot blasting: a machine fires steel shot at the floor and recovers it with a vacuum. It is fast on large open areas and gives an even texture, but does not flatten high spots. Husqvarna's shot blasting guidance explains that shot size and machine speed set the profile.

Many jobs use both: shot blasting on open floor and grinding at edges, joints and around columns. Make sure the scope covers edges and corners, not just the open aisles.

What has to be removed before profiling?

Anything that stops the epoxy from reaching sound concrete must come off first:

  • Old coatings and paint.

  • Sealers and curing compounds, which can be invisible but block the bond.

  • Oil, grease and chemical spills, common near machinery and in loading areas.

  • Weak, dusty or damaged concrete.

Tell the contractor what is known about the floor's history. Deep oil contamination may need cleaning or extra grinding beyond the normal pass, and a small test area confirms the method works before the full floor is done.

Cracks and broken joints need repair before coating. Our article on repairing industrial concrete cracks before epoxy covers that step.

Which moisture tests are used before epoxy?

Moisture rising through the slab is a common cause of epoxy blistering, so the floor is tested before coating. Two ASTM tests are standard:

  • Relative humidity probes: ASTM F2170-19a measures the humidity inside the slab using probes set in drilled holes.

  • Calcium chloride test: ASTM F1869-23 measures how much moisture vapor comes out of the surface over a set time.

The two tests measure different things and their results are not interchangeable. The coating manufacturer sets which test to use and the maximum reading allowed. If the floor is too wet, the options are to wait, use a moisture-tolerant primer or apply a moisture barrier system. RH probes go into drilled holes, so check for embedded conduit first; see concrete scanning before cutting or coring.

How is the prepared surface checked?

Before the primer goes down, check the floor against three things:

  • Profile: compare the surface with ICRI's concrete surface profile chip set, ten rubber replicas of the CSP profiles. Check open areas, edges and repaired spots.

  • Cleanliness: vacuum all dust and look for remaining coating, sealer or oil.

  • Soundness: no loose or crumbling concrete.

Keep prepared areas free of traffic and spills until the primer is applied. If another trade drills or drives across the floor, recheck that area.

How is floor preparation done in a working facility?

Floor preparation can be done in sections while the rest of the building operates. The plan should include:

  • Dust control at the tool. Grinders and shot blasters connected to vacuums with high-efficiency particulate air (HEPA) filters. Concrete dust contains silica, covered by OSHA's respirable crystalline silica standard, 29 CFR 1926.1153.

  • Barriers between the work zone and operating areas, with protection for stored goods.

  • Phasing so aisles and work areas reopen as each section is coated.

If you are still choosing a finish, see our comparisons of grinding and sealing versus epoxy and epoxy versus polyaspartic coatings. Floor preparation is often part of a bigger project too; our article on warehouse refurbishment, renovation and retrofit explains how to scope one.

Frequently asked questions

What concrete surface profile is needed for epoxy?

Most epoxy floor coatings call for a medium profile, often CSP 3 to 4. Always use the profile on the coating manufacturer's data sheet.

Is grinding enough to prepare concrete for epoxy?

Yes, when grinding reaches the profile the coating requires and removes all contamination. Shot blasting is a common alternative on large open floors.

Why do epoxy floors peel?

The most common causes are poor surface preparation, contamination such as oil or sealer, and moisture coming up through the slab.

Can epoxy go over an old sealer?

Usually not. Most sealers block the bond and have to be ground off before the floor is profiled and coated.

How AMS can help

AMS grinds and prepares commercial floors and installs commercial epoxy flooring in warehouses and industrial buildings across New Jersey and Eastern Pennsylvania. We use HEPA dust control, work around your operations and clean up fully. Call 973-354-6550 or request a free quote.

Accurate Maintenance Services

Need help with a project like this?

We handle loading dock repair, concrete cutting, floor work and warehouse renovations across New Jersey and Eastern Pennsylvania — in active facilities, with minimal downtime.

Get a Free Quote Call 973-354-6550
Previous
Previous

Loading Dock Ramp Repair: Fixing the Approach Slab Trucks Drive On

Next
Next

Safety Bollards for Warehouses and Loading Docks: Types, Placement and Installation