Concrete Scanning Before Cutting or Core Drilling: What It Finds and Why It Matters

Quick answer: Concrete scanning locates rebar, post-tension cables, conduit and pipes inside a slab or wall before it is cut or cored. The two main methods are ground penetrating radar (GPR), which works from one side, and concrete X-ray, which needs access to both sides. Scanning lowers the risk of a strike but cannot rule it out completely.

What can concrete scanning find?

Scanning shows where objects sit inside the concrete so a cut or core can avoid them. The usual targets are:

  • Rebar and wire mesh.

  • Post-tension cables (tendons) in elevated and some ground slabs.

  • Electrical conduit, which may carry live cables.

  • Plumbing and radiant heating pipes.

This is not a complete list. Metal objects show up most clearly. Plastic pipe and empty conduit are harder to detect and depend on the method and conditions.

Scan the whole area the work will touch, not just the center of each hole. A core drill is often anchored to the floor, and that anchor hole needs a clear spot too. For concrete core drilling, agree the hole size and position before the scan so the scanner checks the right area.

Why are post-tension cables such a concern?

Post-tension cables are steel tendons stretched under very high tension to hold up the slab. Cutting one weakens the structure, and because the tendons carry large forces, only experienced specialists should work near them.

The Post-Tensioning Institute's repair guidance lists coring and drilling after construction as a cause of tendon failure. Its technical paper on repairs and modifications notes that in finished buildings, tendon failures usually come from corrosion or from contractors cutting openings into the slab without the right knowledge.

If the building has post-tensioned slabs, scanning is not optional. If a scan shows a tendon near the planned opening, stop and get a structural engineer to decide where the opening can go. Other strikes matter too. A cut conduit can mean an electrical hazard and a power outage, and a cut pipe can shut down part of the building.

Is GPR or concrete X-ray better?

Each method suits different jobs:

  • Ground penetrating radar (GPR): sends radar pulses into the concrete and reads the reflections. It works from one side, so it suits slabs on the ground and walls with access from only one face. Results appear on site and are marked on the surface straight away.

  • Concrete X-ray (radiography): places a radiation source on one side and film or a detector on the other. It gives a detailed image, but needs access to both sides and an exclusion zone while the image is taken.

X-ray work uses ionizing radiation, so OSHA requires trained, competent operators under 29 CFR 1926.53, Ionizing radiation. Rooms above and below may need to be cleared too.

For slabs on the ground with access from one side only, GPR is usually the practical choice, because it does not need access underneath or a radiation exclusion zone.

What are the limits of GPR scanning?

GPR is very useful, but it has blind spots:

  • Metal blocks the signal. The Federal Highway Administration's GPR guidance explains that radar does not pass through metal. Dense top-layer rebar can hide what is underneath, and a metal deck under an elevated slab can hide everything below it.

  • Moisture reduces depth. Wet or freshly poured concrete absorbs the signal and gives weaker results.

  • Depth is limited. Deep objects in thick slabs are harder to find. For very thick slabs, see our article on deep hole core drilling.

  • Plastic is hard to see. Empty PVC pipe and plastic conduit may not show clearly.

Ask the scanning technician to mark uncertain areas and state the depth they could actually read. A scan reduces risk. It does not prove an area is clear.

How are scan results used?

The technician marks findings directly on the concrete, usually with colored paint or crayon, and often provides a short report with photos. The project team then compares the marks with the planned openings:

  • Move the opening a few inches if the use allows it, for example a core for a pipe that can shift slightly.

  • Change the cut line for a trench or door opening to avoid a cable or conduit.

  • Get engineering approval before cutting any rebar or tendon that cannot be avoided.

Keep the marks protected until the cutting is finished. If the opening moves outside the scanned area, scan the new location before cutting. For long cuts, scan the whole line, as described in our article on trench drain installation in an existing floor.

When is scanning required or strongly advised?

Scanning is strongly advised before cutting or coring:

  • Post-tensioned slabs, in every case.

  • Elevated slabs, where conduit and pipes often run inside the concrete.

  • Older buildings without reliable drawings, where years of changes may not be recorded.

  • Near electrical rooms and panels, where conduit is concentrated.

  • Large openings, such as door cutouts and trenches, where a strike is more likely.

Some owners and general contractors also require scanning before any cutting by contract. The American Concrete Institute's ACI PRC-228.2-13, Report on Nondestructive Test Methods for Evaluation of Concrete in Structures describes GPR, radiography and other test methods and their limits, for engineers choosing an approach.

Who arranges the scan?

It depends on the contract. The owner, the general contractor or the cutting contractor may arrange it. What matters is that one person is named to:

  • Book the scan and give the scanner the planned opening locations.

  • Share the results with the cutting crew, the trades using the opening and the engineer.

  • Approve changes if an opening has to move.

On jobs with many penetrations, such as MEP core drilling for new plumbing, electrical and HVAC lines, this coordination saves the most time. The same applies to a warehouse refurbishment, renovation or retrofit with many new openings. Our article on when you will need concrete core drilling services covers the common reasons for coring.

Frequently asked questions

Can concrete scanning find everything in a slab?

No. Scanning finds most metal objects, but dense rebar, metal decking, moisture and plastic pipe can hide things. Ask the technician to mark uncertain areas.

What is the difference between GPR and concrete X-ray?

GPR uses radar from one side and shows results on site. X-ray uses radiation, needs access to both sides and requires the area to be cleared while images are taken.

Is it OK to drill through rebar?

Only with approval from the building's engineer. Rebar can often be avoided by moving the hole slightly, which is why scanning comes before coring.

Do I need scanning for a post-tensioned slab?

Yes. Cutting a post-tension cable weakens the slab, and the Post-Tensioning Institute lists coring and drilling as a cause of tendon failure. Scan first and get an engineer involved if a cable is near the opening.

How AMS can help

AMS provides core drilling and concrete slab cutting for warehouses and commercial buildings across New Jersey and Eastern Pennsylvania. We work from scanned layouts, coordinate with engineers and other trades, and control dust and slurry in working facilities. Call 973-354-6550 or request a free quote.

Accurate Maintenance Services

Need help with a project like this?

We handle loading dock repair, concrete cutting, floor work and warehouse renovations across New Jersey and Eastern Pennsylvania — in active facilities, with minimal downtime.

Get a Free Quote Call 973-354-6550
Previous
Previous

Safety Bollards for Warehouses and Loading Docks: Types, Placement and Installation

Next
Next

Trench Drain Installation in an Existing Concrete Floor